12 Commercial Washers and Dryers for Laundromats (October 2026)

If you are opening a self-service laundromat, the best commercial washers and dryers for laundromats are high-extraction front-load coin or card machines paired with tumble dryers, sized at roughly two to three dryers for every washer. That single ratio, and the extraction speed behind it, decides your throughput, your utility bills and how fast each machine pays for itself.

Our team worked through twelve commercial laundry machines for this roundup: coin-operated washers, standalone and stacked washer-dryer combos, high-capacity industrial extractors, and tumble dryers running on gas and electric heat. We lined up capacity, drive type, electrical requirements, drum material and cycle programming side by side so you can see where each machine actually fits in a real store.

One pattern came up again and again in owner discussion: washers are where the downtime and the repair money live, and dryers are comparatively cheap and long-lived. That is why washer extraction speed deserves more of your attention than any other spec on the data plate.

Everything below is written for 2026 equipment decisions, and the shortcodes on each card send you straight to the current listing so you can check the latest specification sheet with the supplier.

Top 3 Picks for Laundromat Owners

These three cover the most common builds: a compact stack for small rooms, a vended storefront dryer with a name buyers recognise, and a high-capacity extractor for institutional linen work.

All 12 Commercial Laundry Machines Compared in 2026

Every machine in the roundup appears below with the specs that actually change your buying decision. Capacity and electrical supply come first because they decide whether the machine physically fits your floor and your service, then we note the drive and control features that affect daily uptime.

1. Splendide DV1725X and WFL2500X Stacked Bundle – Compact Set With Sensor Drying

This bundle pairs a Splendide washer and dryer in one 23.5 inch wide footprint, and it carries the largest public review base in the roundup, 38 reviews averaging 4.3 stars. That matters for a small operator, because almost everything else here is a dealer-sold machine with no published buyer feedback at all.

The interesting engineering is the Opti Sensor moisture detection. Instead of running a fixed timer, the dryer stops when the load is dry, which cuts wear on the drum and reduces the electricity and gas a customer cycle actually consumes.

Programmability is unusually good for a machine this size: nine wash cycles, three dry cycles, adjustable temperature, spin speed and soil level, plus an extra rinse. The controls are touch panels with a digital display, and the app lets an owner start or monitor a cycle from outside the building.

For maintenance I like the Winterization cycle, which matters if the machine sits in an unheated building, and the Tub Fresh drum clean. The vent kit and stack kit are included, so the vertical install is the standard setup.

Where this compact stack fits in a real store

This is a small-format machine. At 2.3 cubic feet it handles a light load and finishes it fast, which suits a studio, a small apartment laundry or a single bay at the back of a store.

It is not a substitute for a 100G vended front loader when you are planning a full self-service floor. Buy it for a compact or mobile build, not as the backbone of a full self-service floor.

What you give up compared with a vended machine

There is no coin slide or card reader, so it cannot run as a self-service earner without an added payment retrofit. There is also no published extraction figure, which means you cannot model dryer count from the specification.

Reviewers report that the reversible dryer door and the choice of stacked or side-by-side layout are what make compact sets work in awkward rooms. The stainless steel drum is listed in the product details, and that is the part worth keeping clean.

2. Speed Queen DR7000WE – Best Recognisable Vended Electric Dryer

Speed Queen is the name owners mention most often when reliability comes up, and the DR7000WE is the electric dryer in that line that fits a self-service floor. Seven cubic feet of drum in a 27 inch wide body is the number that matters here, because dryer footprint sets how many bays you can fit along a wall.

The controls are described as Extreme Tested electronic rather than a mechanical timer, which gives you error reporting and a consistent start across every machine in the room. A fleet of mismatched controls is harder to service than a fleet of identical ones.

Six reviews at 4.3 stars is a small sample, and 27 percent of them sit at three stars, which usually points at feature or control friction rather than build failure. I would not treat that as a reliability verdict either way.

Why electric heat suits some storefronts

Electric needs no gas line, so it is the practical choice in a leased storefront or a building where venting a gas dryer is a permitting headache. You trade a slower heat ramp and a higher power draw for that simplicity.

Check your panel capacity carefully before planning a row of these. Six dryers on one circuit is not a residential electrical question.

Where it falls short of a gas fleet

Gas dryers usually recover a full load faster per cycle, which matters when customers are waiting with wet bedding. Electric is the better answer when the site cannot support gas, not when you want the fastest turnaround.

The thin review base is the other limitation. Owners consistently say a local technician and a parts pipeline matter more than the badge, so confirm service coverage in your region before signing.

3. Wascomat W620cc – Entry Point Into 100G Vended Washing

The W620cc is a 100G class coin and card washer, which puts it in the extraction range that actually reduces dryer time. That is the spec we care most about in a laundromat, and it separates this machine from the compact domestic units that show up in the same aisle online.

Compass Control is the part to pay attention to. Five programs are included as standard, and you can add or delete them, so you can price a short express wash differently from a heavy bedding cycle without buying new hardware.

Heavy Soil and Extra Rinse are the two paid add-ons that raise revenue per cycle in a real store. Customers will pay for both if the machine prompts them clearly, and both options exist here at the factory.

Is 100G extraction worth the utility maths

Yes, because extraction is the one spec that changes your dryer count. A load that leaves the washer at low residual moisture finishes faster and lets one dryer serve more customers per day.

It also shortens the wash cycle in some designs, which is where the Sound Reduction System earns its place on a machine running many cycles.

What you have to source yourself

There are no published owner reviews here, so you are buying on specification and on the reputation of the distributor who installs it. That is normal for this class of machine, but it means you should ask for a written service agreement.

Confirm the 220V supply, the drain run and the water inlet sizes with the installer before the machine is crated. Retrofitting these three items after delivery is the most common source of delay in a build-out.

4. Wascomat W630cc – High-Efficiency Inverter Drive Washer

The W630cc sits one step up from the W620cc and the difference is the drive. A high-efficiency inverter motor adjusts speed continuously rather than stepping through fixed speeds, which means a gentler ramp into the high extraction phase.

On a washer that runs 20 or more cycles a day, that motor behaviour shows up as lower energy cost per load and less stress on the drive components at speed change. Over a service life that is the difference you actually feel in the operating column.

Everything else follows the W-Series pattern: 100G extraction, coin and card payment, five programs under Compass Control, and the Heavy Soil and Extra Rinse paid options.

When an inverter drive earns its cost

It pays off in a high-cycle store, a wash-and-fold operation or a dormitory laundry running long days. In a quiet neighbourhood store with 40 washers turning slowly, the saving shrinks and the acquisition cost matters more.

Ask the distributor for the actual drive type in writing. Several listings in this category describe commercial branding without naming the transmission, and that is exactly the detail you cannot verify later.

How this compares with the W620cc

Functionally the two are close: same extraction class, same control platform, same payment configuration. The inverter drive and the high-efficiency labelling are the real differences, plus the higher acquisition cost.

With no published reviews, treat the specification sheet as the only evidence available and lean on the installer’s warranty terms. Owners repeatedly say the service relationship matters more than the model choice.

5. Wascomat W645cc – Largest Drum in the 100G Line

The W645cc closes the Wascomat 100G trio with the larger-drum platform and the most dispensing capacity. Four compartments matter more than they sound: they let an operator dose pre-wash, main wash, softener and a separate additive, which is how a store sells premium cycles.

The control interface mixes an LED display with dial controls. Dials take abuse from customers better than touch panels, and in a vended room that is a real advantage over the glossy glass you see on domestic machines.

This listing describes the unit as semi automatic in the product fields while the same record lists fully automatic operation elsewhere. Get the operating mode confirmed in writing before you finalise the spec.

When a bigger drum pays off

A larger drum handles bedding, towels and uniforms without overloading, and an overloaded washer is the fastest route to a poor wash and an unhappy customer. On bulky loads you get fewer re-washes and shorter total time per pound of laundry.

For a small express store, the added acquisition cost is harder to recover because you are paying for capacity you do not fill every cycle.

Questions to ask before you commit

Ask for the certified drum volume rather than the 100G label, since extraction class and volume are reported differently by different manufacturers. Confirm the dispenser plumbing layout matches your detergent vendor.

Also confirm the semi automatic versus fully automatic discrepancy, and get the parts list for the drive assembly. That document tells you what the machine will cost you when the extraction motor needs work.

6. WYDDDARY 33 lb Washer Extractor – Stainless Steel Top Loader

This is a 33 lb, 15 kg extractor built for hotel bedding, catering workwear and industrial uniforms rather than for a vended storefront. The drum is 27.5 inches across, the body is 304 stainless steel, and it runs on 220V single phase with 6KW of heat.

The suspension detail stands out. Full bottom suspension with large springs and hydraulic dampers means the machine does not need to be anchored to the slab, which saves real money when you are adding a machine to an existing room.

The 1.5KW inverter gives stepless speed adjustment, and five programmable cycles cover pre-wash, rinse and bleaching. A belt drive is a simple, serviceable combination that keeps the machine quiet.

Why single phase matters for a retrofit

Three-phase power is a building project. Single-phase lets you drop a 33 lb extractor into an existing room without asking the utility company for a service upgrade, which is why this capacity class is popular in secondary spaces.

The cold-water heating system means you do not need a dedicated hot water loop feeding this machine, which simplifies the plumbing plan considerably.

Where the top-load layout costs you

A single detergent compartment limits you to one dosing option per cycle, so premium add-ons are harder to sell than on a four-compartment machine. Top loading also means a wider footprint at 43.3 inches across.

One review at 5 stars is a very small sample and proves little about longevity. Judge it on the stainless steel construction and the belt drive, both of which are the parts that decide whether it lasts.

7. INTSUPERMAI 44 lb 3-in-1 Wash Spin Dry – Highest Capacity in the Roundup

At 44 lb, or 20 kg, this machine takes a very heavy load, and it washes, spins and dries inside one cabinet. For a hotel, a hospital or a restaurant operation that would otherwise move wet linen from one room to another, that consolidation is the whole argument.

The drum is 29.53 inches in diameter with a 17.72 inch depth, and the shell and drum are SUS304 stainless steel. A 2.2KW motor with 6KW of heating runs on 220V three phase at 60Hz.

The suspension uses hydraulics plus springs to control vibration during high-speed dehydration, and the door has a safety lock over tempered glass with an emergency stop button on the panel. That combination matters in an unattended room.

When a 3-in-1 machine is the right call

If your loads are bulky, few and heavy, a combined cabinet cuts the transfer step and the wet linen handling. It also halves the number of machines you have to plumb and power.

It is a poor fit for a customer-facing vended floor, because the two functions cannot run at once on separate loads the way separate machines can.

Plan the electrical work before delivery

Three-phase power is the deciding constraint. A building without it needs a panel upgrade and a licensed electrician, and that work should be budgeted before the machine is ordered.

No power cord is included, because plug types differ by region. Have the wiring planned to the local standard and confirm who is responsible for the connection before the unit arrives.

8. HayWHNKN 33 lb Industrial Washer – Front Load on Single-Phase Power

This front-load washer handles 33 lb of dry clothes on 220V single phase, and the front-load layout is the difference from the top-load extractors in this group. Front loading uses less floor area per pound of capacity and handles bulky items more gently.

The variable frequency drive and inverter motor give stepless speed control, which is what lets a single program serve both a delicate load and a heavy industrial one. A copper wire motor is specified for the drive side.

The drum is 27.5 inches in diameter by 16.9 inches deep, and the body is 304 stainless steel inside and out. Drain hose is included, which is one plumbing item you do not have to source separately.

Why front load suits a small room

The footprint is 42.9 inches wide by 43.3 inches deep, and there is no lid swing to plan around. That matters in a laundry room where the machine sits close to a wall or between two other units.

Front loading also drains predictably, which keeps the floor around the machine drier and reduces the slip risk in a customer area.

Why cycle count is the weak point

Three standard cycles, normal, heavy duty and delicates, is thin for a machine intended to run all day across a mixed customer load. Most operators end up programming more cycles through the controller.

Also note the listed item weight of 1280 pounds. That figure is far heavier than the cabinet dimensions imply, so treat the shipping and handling numbers on this listing as approximate and confirm the real weight with the supplier.

9. EQCOTWEA Coin-Operated Washer Dryer Stack – Turnkey Self-Service Unit

This is a genuine coin-operated self-service machine, washer below and dryer above in one 83 inch tall cabinet that measures 35.4 inches across. For a small store or an apartment laundry, that is a space-efficient revenue machine in the roundup.

Capacity is 26.4 lb, or 12 kg, of dry clothes, with simultaneous washing and drying to reduce the time a customer spends waiting. The drum is SUS304 stainless steel, which is the right material against commercial detergent.

It runs on 220V single phase and draws 6.8A at 1500 watts, with a detergent and fabric softener dispenser on the panel. The coin mechanism is the payment system, so there is no card reader to commission.

Why the stack saves more than floor space

Each cabinet earns from two cycles instead of one, which raises revenue per square foot without adding another drain, another wall and another machine footprint.

Coin operation also avoids the monthly processing fees that come with card and app payment systems, at the cost of accepting coins and coins only.

Read the energy figure carefully

The listed 10950 kWh per year is high for a 12 kg machine and would show up directly in your electricity bill. Ask the supplier what duty cycle that figure assumes before you model the operating cost.

Two wash cycles and one dry cycle is also thin for a vended machine serving strangers. Confirm whether the controller accepts additional programs, and check the footprint figures with the supplier because the published depth and width are mirrored against a very similar model in this roundup.

10. Yokoma Double-Layer Coin Washer Dryer – 12 kg Self-Service Stack

The Yokoma takes the stacked concept further with an upper dryer and a lower washer, so a customer washes on the bottom level, transfers the load upward and finishes it. At 83 inches tall and 41.7 inches wide it is a full-height bay rather than a corner filler.

It is built for self-service use in apartments, hotels, dormitories, gyms and laundromats, with a coin-driven control panel offering timer setting and hot, warm or cold water selection. An automatic locking function holds the machine stable during operation.

The lint filter mounted on the panel is a genuinely useful detail for a vended machine. A dryer that clogs its own airflow starts running long cycles, and customers stop using it.

What the plumbing layout gives you

Rear-mounted dual hot and cold inlets plus a large straight-through drain reduce fill and discharge time, and the straight-through design resists blockages, which keeps a coin machine in service.

An observation window lets a customer see activity inside the drum, which reads as a machine that is working in an unattended room.

Why the single dispenser is a real cost

A single-compartment dispenser on a unit that both washes and dries customer loads limits you to one dosing option. Stores running premium or low-sheen cycles need a multi-compartment machine.

This machine also carries the highest acquisition cost in the group, so it needs the most cycles per day to justify itself. At 1188 pounds listed weight, confirm the actual handling requirement with the supplier as well, since that figure is high for the cabinet size.

11. HayWHNKN 33 lb Commercial Dryer – Heavy Electric Tumble Dryer

This is a 33 lb front-load tumble dryer, and it is the one machine in the roundup whose entire specification is about drying throughput. The drum is 29.5 inches in diameter by 18.9 inches deep with a 1:20 cylinder volume ratio, built from 304 stainless steel.

Heating is 8KW electric on 220V three phase, with a 0.55KW fan and a 0.55KW motor. An over-temperature protector and temperature control are fitted, which is the safety package a code inspector looks for in a public room.

Two numbers matter for a storefront: noise at or below 80 dB(A) and vibration held to 7 mm/s or less. A dryer that shakes hard transfers vibration into the floor and neighbouring units over time.

Do the electrical and venting maths first

Three-phase supply and an 8KW draw per machine means your panel capacity sets how many dryers you can install before a utility conversation. Plan the circuit layout with an electrician during the design phase.

Exhaust venting is a 3.9 inch, or 100mm, connection. Dryers that cannot vent properly run long cycles, burn more energy and fail heaters sooner than the cycle time suggests.

What to check before installation

The machine arrives without coin or card hardware, so a self-service floor needs a payment retrofit or a separate attendant model. Confirm whether the supplier offers a vended version of this platform.

The listed weight of 545 pounds is a realistic figure for a machine this size, and it is worth using when you plan a loading route. Also ask for the warranty terms, because this record lists a one year description that is worth having in writing.

12. EQCOTWEA 35 lb Gas Coin Dryer – Gas Heat on a 110V Supply

Gas heating on a 110V electrical supply is the standout here. The burner does the work, so the electrical demand stays low enough that an existing circuit can carry the machine, and gas usually costs less per cycle than equivalent electric heat at a store doing high volume.

Capacity is 35 lb in a 43.7 by 33.8 by 52.7 inch cabinet weighing 615 pounds, which is a full-size footprint for a vended dryer bay. The drum is SUS304 stainless steel with a burr-free perforated surface.

The LCD touchscreen controller offers five self-service programs and 20 customizable ones, with password protection so customers cannot change parameters. Six languages and Celsius or Fahrenheit switching are built in, along with a two year warranty.

Why gas is the running-cost answer

Per cycle, gas heat usually beats electric for a full 35 lb load, and the 110V electrical requirement means you avoid a panel upgrade for the dryer row. That combination is why many laundromats run a gas fleet.

Forward and reverse drum rotation with a pause between them is listed, and that is what stops bulky bedding from tangling into a single wet mass. On customer loads it produces a noticeably more even result.

What the gas line and venting cost you

A gas connection and code-compliant venting are building work, not appliance work, and they belong in the build-out budget rather than the equipment budget. Get the venting route approved before the machines are ordered.

The published weight of 615 pounds is a realistic figure for a machine this size, and the safety package covers overheat shutdown, motor overload, fire detection and door monitoring, which is the list a local inspector will ask about.

What Type of Washers Do Laundromats Use?

Most self-service laundromats use coin or card operated front-load washers in the 100G extraction class, because high extraction is what lets a load leave the washer close to dry and reduces the dryer count you need. Top-load washers appear in on-premise and multifamily laundry rooms, and stacked washer-dryer combos suit small rooms where every square foot has to earn.

Four configurations cover nearly every build. Vended front-load coin or card washers run a public floor. Industrial extractors with larger drums handle bedding, uniforms and towels. Stacked combos do washing and drying in one cabinet. And on-premise machines sit inside multifamily buildings with restricted access rather than open customer traffic.

The washer type also sets your utility profile. A front-load machine with a high extraction figure uses less water per kilo of laundry and hands the dryer an easier job, and that combination is the core of a profitable room.

How to Size Your Laundromat Fleet: The 1:2 to 1:3 Ratio

The industry rule of thumb is two to three dryers for every washer, and the reason is simple. A washer cycle is fast and a dryer cycle is long, so dryers are always the bottleneck and the machines generating revenue fastest. Real stores drift outside this range, sometimes running far more dryers per washer than the rule suggests, and the ones who fall short on dryer capacity are the stores with customers waiting at the machine.

To size a room, work through it in three steps. Start with the washers your customer base supports, based on the machines you can fit in the available bay space and service comfortably. Then set dryers at two to three times the washer count. Finally, check the floor space, since a dryer needs its own footprint, a lint access route and an exhaust or vent path.

Extraction speed changes step two. A washer that pulls more water out in the spin cycle means a shorter dry time, so the same number of dryers serves more customers. That is why the 100G machines in this roundup are specified the way they are.

If you are planning a small or mid-size build, a stacked washer-dryer combo changes the arithmetic. One cabinet covers two functions in a single footprint, which is useful when the store is compact rather than large.

Why Extraction Speed Cuts Your Dryer Count

Extraction speed, measured in G-force, is the number that determines how much water leaves the load at the end of the spin cycle. Higher G-force means a drier load, a shorter dry cycle and more customers served per dryer per day.

That is why a 100G coin-operated washer is a different product from a compact domestic machine, even when both are called front loaders. The G-force figure tells you what the dryer has to finish, and it is the single spec most worth asking a distributor to put in writing.

Owners also flag a related trend: high-efficiency rinse programmes that reuse wash water, sometimes called grey water rinsing, are appearing in vended and on-premise machines. They cut water consumption per load, which matters where water and sewer charges are a real share of operating cost.

Gas vs Electric Commercial Dryers

Gas dryers usually deliver a faster heat recovery and a lower cost per cycle on full loads, and they need only 110V on the electrical side. Electric dryers need no gas line at all, which makes them far easier in a leased storefront, but they draw far more current and warm up more slowly.

Choose gas when the building has or can get a gas line and the store runs high volume. Choose electric when gas is unavailable or venting a gas dryer is a permitting problem. The Speed Queen DR7000WE in this roundup and the HayWHNKN 33 lb dryer are the electric options; the EQCOTWEA 35 lb gas coin dryer is the gas option.

Both types need planned venting, and neither should be installed without confirming the exhaust route and the electrical or gas capacity with the installer first.

What a Laundromat Equipment Package Actually Costs

Machines are the largest capital line in a laundromat build-out, and the number that surprises first-time owners is everything around the machines. Freight, rigging, installation, utility upgrades and payment hardware are separate line items that land early in the project.

A realistic breakdown has five parts. Equipment covers the washers, dryers and any stacks. Freight and rigging cover moving heavy commercial machines into the building, which often needs a specific doorway or a window removal. Installation covers plumbing, drains, power and gas connection by a licensed trade. Utility upgrades cover panel capacity, a gas line, venting and sometimes a water heater sized for the load count.

Ongoing costs follow a similar structure. Utilities dominate, with dryer heat and water heating as the two large items. Then there is preventative maintenance, parts, a technician on call, insurance, rent and card processing fees if you use card or app payment rather than coins.

Which is why owners treat washers as the budget line and dryers as the stable one. If you are planning a smaller entry, our guide to parts washers for auto shops covers a different kind of wash bay, but the same sizing logic applies to picking a machine that fits the work rather than the biggest one you can fit.

Do not forget the front-of-house and back-of-house cleaning lines either. Our picks for gas pressure washers for heavy-duty cleaning cover the bay floors and exterior approach, which is where a laundromat’s first impression is made.

Where to Buy: Distributor, Dealer or Factory Direct

Most commercial laundry machines in this roundup are not simple online purchase products. They are sold through a regional distributor or dealer who also handles installation, service and parts, and owners consistently point to that relationship as the deciding factor rather than the brand on the data plate.

Buying through the distributor usually means freight, rigging and installation are handled by one party, and the warranty is honoured in your region. Buying factory direct can remove a layer of markup, but you take on the freight, the install coordination and the harder question of who services the machine when a drive motor fails.

Before you sign, ask ten questions. Confirm extraction force in writing. Confirm drum volume and machine dimensions. Confirm electrical supply, phase and amperage. Confirm the gas and venting requirements where a gas dryer is involved. Confirm the warranty length and what voids it. Confirm parts supply and technician coverage in your region. Confirm installation cost and who performs it. Confirm the payment hardware and any processing fees. Confirm the doorway or window access needed to move each machine into the building. And confirm a maintenance agreement and its cost.

Used and refurbished equipment is a legitimate entry path for a small operation, and it carries its own maths. Add the realistic cost of a drive rebuild, a tub seal and a set of bearings before you assume it is cheaper than new, because on machines that is where the money goes.

Reliability, Maintenance and Machine Lifespan

The clearest pattern from owner experience is that washers are the failure point and dryers are not. Owners describe dryers as long-lived, inexpensive to service and easy to fix, while washer downtime is where the lost revenue and the repair bills sit. Plan your maintenance budget accordingly.

Specific failure points come up repeatedly rather than motors. Tub seals, drain hoses, bearings, suspension components and shifter assemblies are the parts that take machines out of service, and plastic gear sets in some transmissions are a recurring theme in owner discussion. Machines built with metal gears and steel drives are widely treated as more durable in vended duty.

Motor horsepower is also over-claimed in marketing. A commercial label on a spec sheet does not tell you the motor size, the gear material or the extraction force, so ask for those three figures directly rather than accepting the word commercial.

A simple routine covers most of it. Clean the lint filters daily. Check the drain hoses and inlet screens monthly. Run the drum cleaning cycle on washers that have one. Keep an eye on the door seals. And have a technician on call rather than waiting for a breakdown, because a machine with a fault sign is a machine that gets fixed before customers start complaining.

Owners with small multifamily units describe being on the breaking point between owning and leasing precisely at the point a machine fails, which is worth weighing if you are running a handful of machines rather than a full store.

Frequently Asked Questions

Final Verdict for Your Laundromat Build

For a full self-service floor, the Wascomat W-Series 100G coin and card washers are the core machines to evaluate, paired with the Speed Queen DR7000WE for electric vended drying or the EQCOTWEA 35 lb gas coin dryer where gas service is available. Those are the machines built for unattended customer duty, and the extraction class is where the economics live.

For a compact or mobile build, the Splendide DV1725X stacked bundle is our top pick in this roundup, with the best public feedback of any machine here and sensor drying that stops the cycle when the load is finished. For institutional linen work, the 33 lb and 44 lb extractors cover hotel, hospital and restaurant volumes without a three-phase upgrade on the smaller models.

Whichever route you take, size dryers at two to three per washer, confirm extraction force in writing, and settle the service and parts arrangement before the machines are crated. If you also run a smaller laundry operation elsewhere, our roundup of hooded dryers for home salons covers the smaller end of the dryer market.

That is the full roundup for 2026. Check the current specification sheet with the supplier, then run your own site survey before the first machine is ordered.